Видео

Good video, thanks for drawing attention to cut ratings on gloves. Just to add, ratings 1-5 are for the old 2003 version of EN388. Ratings A-F are for the newer 2016 version of EN388 (ISO). It uses an improved test method. Broadly old 1-2 = new A. Old 3-4 = new B. Old 5 = new C - F

Where did you find a replacement Splash Guard?? I can't find one anywhere.

My ratchet wont change directions and its a vintage ratchet because its the same one in the video this just makes me more annoyed

I have a 1990 Cherokee XJ, it is the same system as the truck in the video.

I took the arms off and screwed them to the monitor on the floor. Then put the arms on

Great job

Thanks. Made one myself today, looks great!

Good luck dealing with the god dam retainer spring.

Jeep gave us all a proper fuck with this design. Thanks mate for the video!

COLD air kit? Not with that filter location it isn't.

Thanks for video I didn't even know what they were called until I saw your video. Went through a couple that didn't even mention this lever

I'm about to fit my TRD side skirts for the first time. Thank you for the tips!

Just got my Spyder and your vids help a lot. Thanks man for uploading and describing everything so carefully

? Why dont you use Google Lens on your Smart phone to translate it?

Nice video, very informative. Thanks! How low can you bring down the arm? My idea if I purchase this is to mount it on an over- head shelf just over my desk so the arms will be drawn downwards. Can tjis be achieved with this device?

Exactly what I searched for: a video showing the usb cable instalment. 👍🥳

At around 10:15 you commented about a larger seal for the timing chain tensioner. I replaced mine and have the same problem. What did you get?

Where to buy them

Hard to find

I think just saved me a purchase.

This is a fab video. Everything neatly shown and explained (without the standard USA half an hour of rattling on about trips to autozone) Love your Diary Dad !

Hello, I just installed this exact monitor arm but I can't seem to lower the arm in height ? How do you do it ?

One side not working.

Can you cross the monitors ? For example your main is left, but you want to use the right one as main so you put it on left ?

Anyone got a link for the correct size? I cant seem to find them

Very useful video - thank you. Helps me make my choice of arm!

For what it’s worth I put a couple traps on the springs to compress to allow release of the small brackets. I have replaced everything and also done the spring hack inside the handbrake housing but still the handbrake intermittently fails. Thanks for the vid 👍

Plenty of these kits are available in Japan all you have to do is use a proxy service to buy from yahoo auctions. (I know this is five years too late). I've so far got the rear skirt and the side skirts.

One of the best. Excellent show and tell of the process. Thank you!

I just repaired my 2007 jeep liberty. I had to replace the dust shield/backing plates on both sides. I first tried using the 14mm wrench, which I then proceeded to round over the corners of the nuts. Next, I tried using Vise Grip pliers, which I was able to remove 3 of the 8 nuts. Since my dust shields were rusted thru and loose, I removed them. I them used my 4" grinder and ground one side of the nut till the threads were showing, then whit Vise Grips I was able to remove the rest of the nuts. AS the replacement shields were 2 pieces, I did have to remove the Axle. In retrospect, if I had to do this again, I would have removed the Axles. This would have allowed me to use a 6-point socket to remove those nuts. To me, those nuts were interference fit threads. Also, if I had a Oxi-acetylene I would have tried heating them. As you have shown, both of the lever assembles were rusted together. In closing, this was a royal pain in the ass to repair.

Torque looks slower in my opinion. But thank you for the video. Wonder if I can get this app on a Kenwood

that circlip is very difficult to remove. wtf

Where can I get a hardtop like this?

not a complete disassembly.

very clear explanation - thanks.

hello I would like to order this hardtop for my MR2 Mk3 can I have the links for the company please

How did you just pull it through the hole? I have been fighting to get the spring and cable off cause there is no way uts going to just go through

IV same cannon ,I use fx protect Gravity pre wash ,I diluted 1 part to 20 part water,and foams good .good product not expensive either. Lidl pressure washer. It can be diluted at different ratios. Don't use neat to powerful.

I just got a 'Jusfit' china 1/2" , same speed select button and lights, fitted catch ball on the drive, battery isn't as deep is supposedly 580nm 20v. Is stepless pull trigger. It looks a bit snazzier than your one, a mate told me he'd recently got a jusfit Electric chainsaw and it was really good. I'm waiting for a few more parts and tools to arrive before testing it out. Your charger being a clip connection could be better so say, mine has the old 80's power pack cylinder plug .

I could care less about the box, its going in the trash anyway. I care about the product and how it works.

Hi, I got the same unit but still running on kitkat 4.4.44 Is there any way to upgrade the software as I can't get any apps from the play store etc. Many thanx

Nice build, I found the same original GV with the box and all accessories in it (it's a brand new car and I saw it). My friend told me he found it on eBay and wanted to sell it back at a good price! I love the car as it is not been used at all. Do you know how much it will be worth nowadays?

Hi i cant seem to fond the app was it discontinued?

Have one question ❓ can you use with a Android tablet? Do you need to have Internet to use it?

Quite a helpful video thanks.. could you please link the usb 3.0 cable description?

no removal of the vinyl roof? just extra weight = slower

Wow, thank you. Wish I knew this before I just "downgraded" my factory speakers in my Ford.

Nice car and videos

Can anybody help me with the size of this bushing? I would prepare it on my lathe machine before I dismount the car. Thank you

Nice informative and useful video